60 Series Land Cruiser High Clearance Rear Bumper Kit

From: USD$706.33

This is a high clearance DIY weld-together bumper kit for the (1980-1990) 60 Series Toyota Land Cruiser. It provides full wrap-around protection for the rear of your FJ60 while the sloped, high clearance design hugs the rear of the vehicle for unbeatable ground clearance and departure angle. Simply put, you can not get any more rear end clearance than this without cutting into the body of your Land Cruiser! This bumper is a direct replacement for the factory rear bumper but also wraps around the sides of the body for total quarter panel protection. The rear quarter panels are often the most vulnerable piece of body work on a 4x4. Keep them protected!

SKU CO138644 Categories ,


When we set out to design this bumper, we wanted to create something that packed as much functionality as possible while still looking great and complementing the lines of the iconic 60-Series Land Cruiser. The low profile wrap-around design and optional side hoops will take your Land Cruiser’s offroad performance to new levels. The sloping rear profile and optional recessed hitch receiver further increase clearance and provide a smooth surface to slide over obstacles. These features make a very noticeable difference during deep ditch crossing and steep obstacle climbs where other aftermarket bumpers with bulky rear profiles will hang up and impede progress on the trail. Simply put, this bumper allows you to forget about departure angle and substantially improves the offroad capability of your 60 Series Cruiser

The main section of this bumper is CNC-bent out of a single piece of  3/16″ P&O Steel. This greatly reduces the amount of welding and grinding required by you and makes for a cleaner finished product. If you are paying to have the bumper assembled by a welding shop, this significantly lowers the cost.

We realize that at the age they are now at, many 60 Series Cruisers can have frames that are rusty or otherwise damaged in some way. For this reason, we went completely overkill with the mounting system for this bumper. It includes 10 mounting points per side for a total of 20 mounting points! These mounting points use factory holes in the frame and are distributed over a massive 16″ of length of the main frame rails. While this is overkill, it ensures the impact and pulling forces are distributed evenly over the vehicle frame. This also results in wrap-around side wings that are properly supported and worthy of real offroad abuse.

Unlike many aftermarket bumpers that are more or less empty shells with minimal reinforcement, this bumper contains extensive internal ribbing and mounts to the bottom and sides of the vehicle frame for unmatched strength and stiffness. The bumper side wings are tied directly into the vehicle frame using gusseted support brackets, meaning they can take serious offroad hits without flexing into the vehicle body. With this bumper, you’ll be able to tackle challenging trails with a new level of confidence knowing that the rear end of your 60 Series is now nearly invincible!

The low-profile design of this bumper keeps the weight extremely reasonable at 109lbs in steel and 54lbs in aluminum while maintaining excellent strength. This is especially noteworthy when you consider the fact that the factory hitch receiver, frame crossmember and rear bumper all get removed before installing the Coastal Offroad bumper. This means that even with our steel bumper version, the total weight increase to your vehicle is negligible at best. This minimizes added stress on your vehicle, maintains precious payload capacity, and allows you to keep your factory suspension if desired.

We finished this bumper off with integrated light buckets for surface mount LED pod lights (custom light cut outs available by request), a recessed hitch receiver, and heavy duty 9/16″ recovery points that are placed directly in line with the vehicle frame to eliminate any leveraging effects. These recovery points are formed by laser cut steel plates that pass through the bumper shell and bolt directly to the Land Cruiser’s frame as part of the bumper’s main mounting brackets. The recovery points then get welded to the in and outside of the bumper shell. These factors all combine to form recovery points that minimize stress on your Land Cruiser’s frame and provide reliable recoveries of heavily loaded vehicles in the worst of offroad situations. To further protect the vulnerable rear corners of your Land Cruiser, this bumper is available with optional tubing side hoops that will help push your Land Cruiser away from trees and rock walls.

**Please note that some of the later year 60 Series Land Cruisers have a large factory crossmember that spans the rear of the vehicle frame. This bulky crossmember reduces ground clearance and makes it impossible to fit a slim, high clearance bumper that complements the lines of the vehicle. For this reason, this crossmember must be removed to install this bumper. Earlier model year Land Cruisers did not have this factory crossmember and the bumper is thus a direct fit.

The swing out tire carrier comes in either a single or dual sided configuration and is built to accept a tire up to 37″ in diameter! Both carriers include mounting brackets for a hilift jack and other recovery items. The dual swing out includes the hilift mount as well as a lockable jerry can holder designed to fit two 20L NATO style jerry cans. These carriers feature heavy duty chromoly heim joint hinges, 2000lb toggle latches, T-handle spring pins, and a replaceable UHMW catch pad that provides secure, rattle free operation. The heim joints in conjunction with the toggle latch provide tons of adjustability, allowing for easy assembly and guaranteed alignment of the carrier latch. The single swing out add-on weighs 34lbs and the dual swing out add-on with gas can holder weighs 77lbs.

•DIY Weld-together kit – This bumper arrives as precision CNC-laser cut pieces that you then weld together (detailed assembly instructions included)

•CNC-bent plates greatly reduces amount of welding and grinding required by you and makes for a cleaner finished product

•Slim profile is engineered to provide maximum ground clearance and complement the factory body lines

•Heavy duty 3/16″ plate steel construction for maximum offroad strength and durability

•Optional 1/4″ 5052 aluminum construction for a lightweight yet very durable overlanding setup (55lb weight savings)

•Optional recessed 2″ hitch receiver for a clean look and further clearance gains (While the hitch is very well reinforced, we cannot rate it for on-road towing due to the DIY welding nature of this kit)

•Bolts directly to frame using 20 factory mounting points for unbeatable strength – uses factory mounting holes

•Reinforced 9/16″ thick clevis mounts allow the use of 3/4″ D-Rings and pull directly off of the frame for confident recoveries of heavily loaded vehicles

•All kits ship as clean, bare metal that is ready to weld out of the box – the Nitrogen laser cutting technology means no cutting edge oxidation and thus easier and stronger welds

•Optional Single and Dual Swing out carriers with spare tire mount, hilift jack mount and locking dual NATO can holder (dual swing out only)


Forget the outrageous lead times of many bumper options that are measured in months. All of our bumper kits ship within 3-10 business days with 2-day shipping

Bumper assembly

As for welding, with everything designed using CAD software and then CNC laser-cut to size, the pieces fit together perfectly and this makes for a very simple assembly process. All kits come with detailed instructions with plenty of clearly labelled diagrams that are made using cutting-edge CAD software. This bumper kit is well within the ability of a novice welder and many customers have purchased it as their very first welding project with great results! This is made possible by the clean parts fit-ups and thick material. These are two factors that make welding significantly easier. Welding is one of those skills that is easier to learn than you may think and once you can do it, you’ll wonder how you ever got by without it. Alternatively, many individuals buy the kits and then have a local welder assemble it for them. Even in this case, it typically ends up being less expensive than buying a pre-fabricated bumper – especially after considering the lower shipping costs of our kits vs. fully assembled bumpers.

Bumper weight

Steel base bumper weight: 109lbs
Aluminium base bumper weight: 54 lbs


There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Wondering what is involved in assembling and welding this bumper kit?

Watch the video below to see 4th Gen 4Runner Owner Garrett Logan run through the process and gives his thoughts along the way.
(The 4th gen 4runner is shown, but the build process is nearly identical to this bumper).

Wondering what is involved in assembling and welding this bumper kit?

Watch the video below to see 4th Gen 4Runner Owner Garrett Logan run through the process and gives his thoughts along the way.

Don't see exactly what you're after?

We at Coastal Offroad are more than happy to work with our customers to design their dream bumper. Feel free to send us an email (support@coastaloffroad.com) for any custom requests.