2004-2015 Nissan Titan Low Profile Rear Bumper Kit

From: $633.27

This is a low profile DIY weld-together rear bumper kit for the 1st generation (2004-2015) Nissan Titan. This bumper provides substantially increased ground clearance and rear end protection over the stock bumper. This has been achieved through the use of 3/16" thick plate steel (optional 1/4" aluminum available) and a sleek profile that sits tighter to the tailgate than the stock bumper. To top it off, this bumper comes with built-in mounts for the stock license plate lights and reverse sensors. Simply remove them from your stock bumper and pop them into the CNC cut holes in this bumper. No splicing or extending of wires required.  Additionally, it requires no modifcation to the frame or bedsides of the truck and uses all factory mounting points. The sloping rear profile and recessed hitch receiver further increase clearance and provide a smooth surface to slide over obstacles, significantly improving the offroad capability of your Titan!

SKU CO0932 Categories ,

Description

The profile of this bumper has been designed with maximum ground clearance and departure angles put first. The bumper sits as high and tight to the rear frame crossmember of the 1st generation 2004-2015 Nissan Titan as possible, while the angled side wing faces will smoothly slide over obstacles and ensure you do not get hung up on the trail. The side wings of this bumper provide heavy duty plate protection that wraps underneath the vehicle. These side wings will take a serious hit without flexing or deflecting into the vehicle body. The hitch receiver in this bumper is recessed into the bumper and angled at a 45 degree angle so it will smoothly slide over obstacles and ensure you do not get hung up on the trail. These features make a very noticeable difference during deep ditch crossing and steep obstacle climbs where other aftermarket bumpers with bulky rear profiles and protruding hitch receivers will hang up and impede progress on the trail. Simply put, this bumper allows you to forget about departure angle and substantially improves the offroad capability of your Titan!

We finished this bumper off with optional single and dual swing out carriers, two integrated light buckets for surface mount LED pod lights (custom cut outs available by request), and heavy duty 9/16″ recovery points that are placed directly in line with the Nissan Titan frame to eliminate any leveraging effects. These recovery points are formed out of laser cut steel plates that pass through the bumper shell and tie directly into the bumper’s main mounting points on the Nissan Titan frame. The recovery points then get welded to the in and outside of the bumper shell. These factors all combine to form recovery points that minimize stress on your Nissan Titan frame and provide reliable recoveries of heavily loaded vehicles in the worst of offroad situations. What could make this bumper even better? The low profile design has resulted in very reasonable weights of 90lbs for the steel bumper and 44lbs for the aluminum version. Considering that this bumper replaces your factory bumper, hitch receiver and associated components, the resulting weight increase to your Nissan Titan is surprisingly minimal. This reduces added stress on your vehicle, maintains precious payload capacity, and allows you to keep your factory suspension if desired.

Don’t want to lose your factory parking sensor system? No problem. This bumper kit comes with CNC-cut ports for each of the 4 factory parking sensors as well as internal routing ports for the factory wiring harness to pass through without any modification or extensions required. Simply pop the sensors into this replacement bumper, route the factory harness through the internal ports, and plug it back into the vehicle. The factory wiring harness is easily removed from the stock bumper and transferred to the Coastal Offroad bumper. When removing the Coastal Offroad bumper from the vehicle, all wiring is then conveniently disconnected all at once via the factory plug.

The swing out tire carrier comes in either a single or dual sided configuration and is built to accept a tire up to 37″ in diameter! Both carriers include mounting brackets for a hilift jack and other recovery items. The dual swing out includes the hilift mount as well as a lockable jerry can holder designed to fit two 20L NATO style jerry cans. These carriers feature heavy duty chromoly heim joint hinges, 2000lb toggle latches, T-handle spring pins, and a replaceable UHMW catch pad that provides secure, rattle free operation. The heim joints in conjunction with the toggle latch provide tons of adjustability, allowing for easy assembly and guaranteed alignment of the carrier latch. The single swing out add-on weighs 34lbs and the dual swing out add-on with gas can holder weighs 77lbs.

•DIY Weld-together kit – This bumper arrives as precision CNC-laser cut pieces that you then weld together (detailed assembly instructions included)

• Slim profile is engineered to provide maximum ground clearance and complement the factory body lines

• Fully compatible with the factory license plate lights and parking sensors – simply pop them out of your stock bumper and into this replacement bumper

• Heavy duty 3/16″ plate steel construction for maximum offroad strength and durability

• Optional 1/4″ 5052 aluminum construction for a lightweight yet very durable overlanding setup (46lb weight savings)

• Recessed 2″ hitch receiver for a clean look and further clearance gains (While the hitch is very well reinforced, we cannot rate it for on-road towing due to the DIY welding nature of this kit)

•Compatible with some factory and aftermarket hitch receivers – please email us photos of your hitch receiver for confirmation

• Mounts directly to the frame using 8 factory mounting points – no drilling required.

•Reinforced 9/16″ thick clevis mounts allow the use of 3/4″ D-Rings and pull directly off of the frame for confident recoveries of heavily loaded vehicles

• All kits ship as clean, bare metal that is ready to weld out of the box – the Nitrogen laser cutting technology means no cutting edge oxidation and thus easier and stronger welds

•Optional Single and Dual Swing out carriers with spare tire mount, hilift jack mount and locking dual NATO can holder (dual swing out only)

•Integrated LED light mounts in the bumper include slotted mounting tabs that give tons of adjustment to fit a variety of lights

Additional information

3/4" Recovery Shackle (Pair)

,

Body Lift Adjustment (NOT suspension lift)

, , , ,

Cree LED Lights

, , , , , , , ,

Recessed 2" Receiver

,

Swing Out Tire Carrier

, ,

Tubing

, ,

Bumper assembly

As for welding, with everything designed using CAD software and then CNC laser-cut to size, the pieces fit together perfectly and this makes for a very simple assembly process. All kits come with detailed instructions with plenty of clearly labelled diagrams that are made using cutting-edge CAD software. This bumper kit is well within the ability of a novice welder and many customers have purchased it as their very first welding project with great results! This is made possible by the clean parts fit-ups and thick material. These are two factors that make welding significantly easier. Welding is one of those skills that is easier to learn than you may think and once you can do it, you’ll wonder how you ever got by without it. Alternatively, many individuals buy the kits and then have a local welder assemble it for them. Even in this case, it typically ends up being less expensive than buying a pre-fabricated bumper – especially after considering the lower shipping costs of our kits vs. fully assembled bumpers.

Bumper weight

Steel base bumper weight: 90lbs
Aluminum base bumper weight: 44 lbs

Shipping

Forget the outrageous lead times of many bumper options that are measured in months. All of our bumper kits ship within 3-10 business days with 2-day shipping

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Wondering what is involved in assembling and welding this bumper kit?

Watch the video below to see 4th Gen 4Runner Owner Garrett Logan run through the process and gives his thoughts along the way.
(The 4th gen 4runner is shown, but the build process is nearly identical to this bumper).

Wondering what is involved in assembling and welding this bumper kit?

Watch the video below to see 4th Gen 4Runner Owner Garrett Logan run through the process and gives his thoughts along the way.

Don't see exactly what you're after?

We at Coastal Offroad are more than happy to work with our customers to design their dream bumper. Feel free to send us an email (support@coastaloffroad.com) for any custom requests.